RAM-B-201U

The Powder Coated Marine Grade Aluminum Standard 3.0'' Double Socket Arm has a socket at either end to allow a 1'' diameter ball accessories to be connected.

A tightening screw on the side of the arm enables the sockets to clamp firmly to a RAM 1'' diameter ball. When loosening the side screw, a single spring inside the arm opens the sockets allowing you to pivot the ball and socket connection or completely disconnect the ball from the socket.

The arm length is 3.0'' when measured from socket center to socket center. The total length of the arm is 3.69''.

RAM DESIGN VIEW E-DRAWINGS:
 

To view the design specifications of the RAM-B-201, click here. The pdf file shows all of the information you need to know about this RAM Mounting Component.

RAM-B-201U-C

The Powder Coated Marine Grade Aluminum LONG 5.25'' Double Socket Arm has a socket at either end to allow a 1'' diameter ball accessories to be connected.

A tightening screw on the side of the arm enables the sockets to clamp firmly to a RAM 1'' diameter ball. When loosening the side screw, a single spring inside the arm opens the sockets allowing you to pivot the ball and socket connection or completely disconnect the ball from the socket.

The arm length is 5.25'' when measured from socket center to socket center.

RAM-B-202U

The Marine Grade Aluminum Universal Plate has a 1.0'' diameter Rubber Ball connected at right angles to a 2.5'' diameter Plate. The plate has pre-drilled holes in the base plate, including the universal AMPS hole pattern. If required, the different hole patterns allow you to connect this plate to almost any type of existing hole pattern.

NOTE: This base plate will attach to any of the RAM plastic HOL cradles, but generally the RAM-B-238 Diamond Plate is used.

MOUNTING SOLUTIONS:
Mounting hardware is NOT included with the purchase of the RAM-B-202.

RAM-B-202 E-DRAWINGS:
Click the graphic  to view the design drawings for the RAM-B-202. The pdf file shows the spacing distances for the hole pattern on the plate and the exact location and height of the 1.0'' ball.

RAM-B-231ZU

The Marine Grade Aluminum Rail Base has a 1.0'' diameter Rubber Ball designed to sit at right angles to the mounting rail. The Zinc Coated metal U-Bolt and nuts included will fit a circular rail with diameter from 3/4'' to 1.0''.

To mount the rail base, place the top of the base on the rail and then slide the u-bolt around the rail, into the holes in the base. Now tighten the screws onto the u-bolt until the base is clamped firmly. If you desire, you can slot the black plastic covers over the exposed ends of the u-bolt.

For a larger rail, you can purchase the RAM-B-231LZS Large Rail Base for circular rails with diameter from 3/4'' to 1 1/8''.

NOTE: This base is NOT rust proof. If you are looking to use this mount in the elements, we suggest the RAM-B-231 Stainless Steel U-Bolt Mount.

RAM-B-236U

RAM-B-238U

The Powder Coated Marine Grade Aluminum Universal Plate has a 1.0'' diameter Rubber Ball connected at right angles to a 1 1/4'' x 2 1/2 '' Diamond Plate. The plate has two holes 1.912'' from center to center, positioned at either tip of the diamond plate.

NOTE: This base plate will attach to any of the RAM plastic HOL holders and the industry standard AMPS hole pattern.

RAM-B-238 E-DRAWINGS:
Click the graphic to view the design drawings for the RAM-B-238. The pdf file shows the spacing distances for the hole pattern on the plate and the exact location and height of the 1.0'' ball.

RAM-HOL-UN2U

The Medium RAM Plastic Side Clamping Cradle is designed to hold a large amount of different kinds of cell phones and electronic devices.

USING THE CRADLE:
This cradle has padded locking side clamps that close tightly on the item you want to hold. To release the clamp hold, simply press the button found at the bottom of the back of the cradle which will spring the clamps open. At the base of the cradle is a small support to hold the bottom of the item securely in the cradle.

IMPORTANT CRADLE USE:
The RAM side clamping cradle is designed to be used in a closed cabin environment. The side clamping cradle is only a light weight cradle and may not hold your device in a high vibration situations as found on a motorcycle.

CRADLE DIMENSIONS:
  Minimum Width:  2.22''
  Maximum Width:  3.75''
  Side Clamp Height:  5.0''
  Side Clamp Depth:  1.25'' (at maximum point)
  Cradle Height:  4.0''

NOTE: The top of the cradle is open, so the items in the cradle can be larger than the height of the cradle.

If you require a different sized side clamping cradle there are three other options available.

INCLUDED WITH THE CRADLE:
The cradle includes a set of two nuts and bolts to connect the cradle to any of the RAM compatible mounts.

IMPORTANT MOUNTING INFORMATION:
If you already own the cradle shown above, or any other cradle with a hole pattern that will match the RAM Diamond Plate hole spacing, then you require one of the RAM Assemblies listed below. If you are looking to purchase a complete mount for the above cradle, take a look at the Complete Mount list below.

The cradle does not ship with a RAM ball. To add a 1'' ball to this cradle you need to purchase either the Aluminum Diamond Plate with 1'' ball (RAM-B-238) or Plastic Diamond Plate with 1'' ball (RAP-B-238). If you need to mount this cradle on a 1.5'' ball system, you will require the Aluminum 2.5'' diameter Round Plate (RAM-202) as RAM does not make a Diamond plate in the 1.5'' ball size.

RAM-HOL-CO5P

The RAM High Strength Plastic POWERED Cradle is designed to hold the complete Compaq iPaq PDA Series

PLACING YOUR GPS INTO THE CRADLE:
Place the top of the PDA into the top spring loaded hook arms, and push the arms up. Now swing the bottom of the PDA into the cradle and carefully lower the PDA into the power plug at the bottom of the cradle.

INCLUDED WITH THE CRADLE:
The cradle includes a set of two nuts and bolts to connect the cradle to any of the RAM compatible mounts.

IMPORTANT MOUNTING INFORMATION:
If you already own the cradle shown above, or any other cradle with a hole pattern that will match the RAM Diamond Plate hole spacing, then you require one of the RAM Assemblies listed below. If you are looking to purchase a complete mount for the above cradle, take a look at the Complete Mount list below.

The cradle does not ship with a RAM ball. To add a 1'' ball to this cradle you need to purchase either the Aluminum Diamond Plate with 1'' ball (RAM-B-238). If you need to mount this cradle on a 1.5'' ball system, you will require the Aluminum 2.5'' diameter Round Plate (RAM-202) as RAM does not make a Diamond plate in the 1.5'' ball size.

Fits the HP ipaq 4705

RAM-HOL-CO2P

The RAM High Strength Plastic POWERED Cradle with expanding top is designed to hold the following Compaq iPaq units,
  • Compaq iPaq h3100 Series
  • Compaq iPaq h3600 Series
  • Compaq iPaq h3700 Series
  • Compaq iPaq h3800 Series
  • Compaq iPaq h3900 Series
  • Compaq iPaq h5100 Series
  • Compaq iPaq h5400 Series
  • Compaq iPaq h5500 Series

EXPANSION PACKS: This cradle will hold your PDA if connected to an expansion pack, a NAVMAN 3450, or left in the original protective cover.

PLACING YOUR GPS INTO THE CRADLE:
Place the top of the PDA into the top spring loaded hook arms, and push the arms up. Now swing the bottom of the PDA into the cradle and carefully lower the PDA into the power plug at the bottom of the cradle.

ASSEMBLY REQUIRED FOR THE RAM-HOL-CO2P:
The RAM-HOL-CO2P Powered Cradle requires some assembly. The cradle ships with two (2) Null Modem Wires and three (3) circuit boards that you need to assemble prior to using the powered cradle. For more information, take a look at the Owners Manual for the RAM-HOL-CO2P Cradle page (pdf file).

INCLUDED WITH THE CRADLE:
The cradle includes a set of two nuts and bolts to connect the cradle to any of the RAM compatible mounts.
 

MPORTANT MOUNTING INFORMATION:
If you already own the cradle shown above, or any other cradle with a hole pattern that will match the RAM Diamond Plate hole spacing, then you require one of the RAM Assemblies listed below. If you are looking to purchase a complete mount for the above cradle, take a look at the Complete Mount list below.

The cradle does not ship with a RAM ball. To add a 1'' ball to this cradle you need to purchase either the Aluminum Diamond Plate with 1'' ball (RAM-B-238). If you need to mount this cradle on a 1.5'' ball system, you will require the Aluminum 2.5'' diameter Round Plate (RAM-202) as RAM does not make a Diamond plate in the 1.5'' ball size.